We're going up.
“The psychological tools I’ve gained from bodybuilding will never atrophy.”
Tom Platz
“I wanted to show I could do it on their terms. If I could show them I could lift with correct technique, that’s how I would win respect. I let my lifting do the talking.”
Judy Glenney
Enter a weight you lifted and how many reps you did. Choose an experimental or Epley 1RM estimate, then explore projected working weights.
This is a specific targeted rep and weight scheme for competitive weightlifting. Your loading may vary. Your quadratic polynomial regression may vary.
Before proceeding with barbell work, warm up for at least 5 minutes of steady-state work on a SkiErg, C2 BikeErg, C2 rower, or Echo bike.
Your recent set
Sets control the graph only; neither 1RM formula uses set count.
Experimental, kg-based research estimate; not validated against measured maxima. Target loads use reverse Epley.
Variance can break the math: hidden weight adjustments may make displayed values fail to reconcile. It applies with either formula.
Use a challenging set of 1–30 reps for a more useful estimate.
Warm-ups above 15 reps are at the lifter’s discretion. Use common sense.
Enter both values to see your estimated 1RM, warm-ups, and projected working weights.
How it works. Experimental: RM = w × (1 + (r − 1)^0.85 / (−2.55 + 4.58 × ln(w))), with w in kg. Target weights use reverse Epley.
Note: this is only a guide. Estimates vary by lift, fatigue, and individual; use judgment and choose safe loads.
Set vector EXPERIMENTAL
1RM is the origin. The graph plots projected working and warm-up loads below it. Inputs stay in sync with the Calculator tab.
Sets control the graph only; neither 1RM formula uses set count.
Experimental, kg-based research estimate; not validated against measured maxima. Target loads use reverse Epley.
Variance can break the math: hidden weight adjustments may make displayed values fail to reconcile. It applies with either formula.
Direction mapping
Warm-ups above 15 reps are at the lifter’s discretion. Use common sense.
Sets relative to 1RM
In Load mode, each component is a load difference from 1RM, so X, Y, and Z all use the selected weight unit (lb or kg).
Graph key: 1RM is the origin (0,0,0). X/Y/Z are load-difference components; scale fits only the displayed set and warm-ups.
Accessory flow
Select the lift that matches your calculator set. Its computed 1RM sets the accessory load ceilings below, all at 60% or less. Loads always snap to equipment sizes, independently of the calculator’s snap toggle.
Select a lift to generate your two-accessory flow.
Dumbbells: 5–80 lb in 5 lb steps, then 100 lb at a 95 lb target if below the 60% ceiling. Metric displays convert that inventory to kg. Kettlebells: 4–48 kg in 4 kg steps, or nominal 9, 18, 26, 35, 44, 53, 62, 70, 80, 88, 97, 106 lb. Barbells: 15 and 20 kg (rounded to 33 and 44 lb). Available plates: 1.25, 2.5, 5, 10, 15, 25, 45 lb, loaded equally on each side; quantities assume enough matching pairs.
Percentages are total external load relative to the selected main lift’s computed 1RM, not a tested max for each accessory. Follow the prescribed loads, sets, and reps; do not round above the ceiling. These are separate accessory sets, not warm-ups. Bench variations require a stable bench; barbell squats require safe rack access. If the empty bar exceeds the target, use a lighter implement or skip that movement. Stop if a movement causes pain.
Olympic
Choose one lift and a target top single in kg. The reference ramp fixes the number of sets: 9 for snatch, 8 for clean and jerk. Every set is one single; clean and jerk means one clean plus one jerk.
Each reference set is scaled by target ÷ reference top, then rounded to the nearest 1 kg. The final set equals your target. The initial 15 kg reference entry is excluded. Polynomial fits are descriptive only and are not used to prescribe loads. Calculator formula, variance, and snap settings do not affect this plan.
Metric loading is primary: use a 15 kg bar with 25, 20, 15, 10, 5, 2.5, 2, 1.5, 1, or 0.5 kg plates. Total loads snap to whole kilograms (1 kg increments using paired 0.5 kg plates). When round down and round up match, one exact metric option is shown.
Imperial loading is secondary: use a 35 lb bar with paired 2.5, 5, 10, 15, 25, or 45 lb plates. Pound-plate conversions are inexact alternatives, not extra sets: choose only one load per set. The nearest buildable loads below and above each kg prescription are shown in pounds, not as fractional kg totals. The upper option may exceed the prescription or target.
All plate instructions are per side and assume enough matching pairs. The final three metric sets include two 2.5 kg collars (5 kg total) within the prescribed weight; earlier metric sets exclude collar weight. Every imperial set includes approximately 0.5 lb per collar (1 lb per pair), rounded from 193.56 g each to the nearest ¼ lb. If the bar plus required collars exceeds a prescription, no lower loading option is available.